Distributed and polarimetric pressure sensitivity in spun highly birefringent optical fibers.

We examine experimentally the influence of the fiber inelastic twist on polarimetric sensitivity to hydrostatic pressure and pressure sensitivity in a Rayleigh-scattering-based optical frequency-domain reflectometer (OFDR) for highly birefringent side-hole fibers. The fibers were drawn from the same preform with different spin pitches varying from 5 mm to 200 mm. We also demonstrate that the sensitivities of spun fiber can be estimated analytically based on its spin pitch, measured birefringence, and the sensitivity of the corresponding non-twisted fiber, showing good agreement with the experimental results. We proved that polarimetric sensitivity to pressure decreases with the shorter spin pitches, while distributed pressure sensitivity decreases for the one polarization eigenmode and increases for the second polarization eigenmode. Therefore, the spun-fibers can operate well as the polarimetric sensors of other physical parameters inducing circular birefringence even under varying pressure. Moreover, they can be used to obtain the desired difference between sensitivities for both polarization eigenmodes.

Synthesis of CdSe Quantum Dots in Two Solvents of Different Boiling Points for Polymer Optical Fiber Technology.

Polymer materials find many applications in various industries. Efforts are being made to obtain structures with increasingly better properties. It is necessary not only to obtain new materials but also to modify existing structures. Such is the situation with polymer optical fibers. The widespread use of polymer optical fibers is impossible, due to their very high optical losses compared to glass optical fibers. The solution to this problem can be the manufacturing of polymer active optical fibers. Active fibers are the basic components of fiber optic amplifiers and lasers that allow the direct amplification of light inside the fiber. In order for their operation to be the most effective, it is necessary to use dopants. The most commonly used are lanthanide ions isolated from the polymer network, active organic dyes, and quantum dots. These dopants are characterized by very high luminescence and long glow times. Quantum dots of CdSe are made using two organic solvents that differ in boiling points-hexane (a low-boiling solvent with a boiling point of 69 °C) and 1-octadecene (a high-boiling solvent with a boiling point of 315 °C). This work aims to test whether the type of solvent used to obtain quantum dots affects the doping capabilities of polymer structures, from which optical fibers can then be drawn.

Fiber-based vortex beam source operating in a broadband or tunable mode.

We demonstrate a fiber-based optical vortex beam source operating in broadband or tunable mode in the spectral range of 1100-1400 nm. The vector vortices of the total angular momenta equal to +2, 0, and -2 are obtained by converting the respective linearly polarized (LP11) modes of the two-mode birefringent PANDA fiber with stress-applying elements by gradually twisting its output section. At the input end, the PANDA fiber is powered by broadband supercontinuum or tunable Raman solitons generated in the LP11 polarization modes of a birefringent microstructured fiber with a specially designed dispersion profile and coupled to the respective LP11 modes of the PANDA fiber. Two pulse lasers operating in different regimes (1 ns/1064 nm and 190 fs/1037 nm) were used as the pump to generate supercontinuum or tunable solitons directly in the LP11 modes of the microstructured fiber purely excited with a special Wollaston prism-based method. The high modal and polarization purities of the beams after successive transformations were experimentally confirmed. We also proved the vortex nature of the output beams using shearing interferometry.

Intermodal Four-Wave Mixing Process in Strain-Induced Birefringent Multimode Optical Fibers.

Our study investigated the partially degenerate intermodal four-wave mixing (IM-FWM) process in nonlinear multimode optical fibers with strain-induced birefringence. The difference in the refractive index along the two orthogonal directions was due to the photoelastic effect that occurred when the fiber under test (FUT) was subjected to uniformly applied diameter stress caused by winding on a cylinder of a given diameter. Our work analyzed how the nonlinear frequency conversion and the output modal field profiles depended on the degree of birefringence in FUT. The experimental results significantly affected the order of the excited moduli in fiber sections characterized by different amounts of birefringence. We also checked the efficiency of the FWM process for different polarizations of the pump beam to determine those for which the FWM process was most effective for the 532 nm sub-nanosecond pulses. More than 30% conversion efficiency was obtained for the FUTs with a length of tens of centimeters.

An Efficient Method for the Intermodal Four-Wave Mixing Process.

We demonstrate a partially degenerated intermodal four-wave mixing (FWM) process realized in a few-mode nonlinear optical fiber, leading to the effective generation of visible red and blue light from 532 nm sub-nanosecond pulses. We present a self-seeded FWM configuration with a signal beam obtained in the additional section of the same type of fiber that ensures perfect matching between the seed and the Stokes beams. Over 40% of the wavelength conversion efficiency in the FWM process was obtained using a fiber length shorter than 1 m.

Sensitivity tailoring of an all-fiber bend sensor based on a dual-core fiber unbalanced Michelson interferometer.

In this work, a compact all-fiber bend sensor based on a dual-core microstructured optical fiber has been manufactured and characterized. The sensor relies on the unbalanced Michelson interferometric technique realized by attaching a piece of silica fiber to one of the fiber cores acting as the unbalancing element. Three probes with different lengths of the unbalancing element have been experimentally tested for sensitivity tailoring analysis. Additionally, a theoretical model has been developed for comparison and verification of the results. Good linear behavior of the spectral shift with bend has been measured and it has been proven that the sensitivity of the sensor depends on the length of the unbalancing element and the orientation of the cores. Higher sensitivities are achieved for shorter lengths of the unbalancing element and orientation of the core axis parallel to the bend direction. The highest sensitivity reported is 9.97 pm/µm for the case of 34 µm of unbalancing element and orientation of 0 degrees.

Simple approach for extending the ambiguity-free range of dual-comb ranging.

Dual-comb (DC) ranging is an established method for high-precision and high-accuracy distance measurements. It is, however, restricted by an inherent length ambiguity and the requirement for complex control loops for comb stabilization. Here, we present a simple approach for expanding the ambiguity-free measurement length of DC ranging by exploiting the intrinsic intensity modulation of a single-cavity dual-color DC for simultaneous time-of-flight and DC distance measurements. This measurement approach enables the measurement of distances up to several hundred kilometers with the precision and accuracy of a DC interferometric setup while providing a high data acquisition rate (≈2kHz) and requiring only the repetition rate of one of the combs to be stabilized.

All-normal dispersion supercontinuum vs frequency-shifted solitons pumped at 1560†nm as seed sources for thulium-doped fiber amplifiers.

We present a direct comparison between two types of femtosecond 2 µm sources used for seeding of an ultrafast thulium-doped fiber amplifier based on all-normal dispersion supercontinuum and soliton self-frequency shift. Both nonlinear effects were generated in microstructured silica fibers, pumped with low-power femtosecond pulses at 1.56 µm originating from an erbium-doped fiber laser. We performed a full characterization of both nonlinear processes, including their shot-to-shot stability, phase coherence, and relative intensity noise. The results revealed that the solitons show comparable performance to supercontinuum in terms of relative intensity noise and shot-to-shot stability, despite the anomalous dispersion regime. Both sources can be successfully used as seeds for Tm-doped fiber amplifiers as an alternative to Tm-doped oscillators. The results show that the sign of chromatic dispersion of the fiber is not crucial for obtaining a stable, high-quality, and low-noise spectral conversion process when pumped with sub-50 fs laser pulses.

Method for increasing coupling efficiency between helical-core and standard single-mode fibers.

Helical core fibers (HCFs) suffer from low coupling efficiency and unavoidable excitation of higher order modes below the cutoff wavelength because of a core tilt with respect to the symmetry axis of the cladding. We propose an effective way of increasing the coupling efficiency to a HCF by untwisting its beginning section in a hydrogen flame. The proposed solution provides also a control over the excitation of higher order modes in HCFs and can be applied in splicing as well as in a free-space launching configuration. We experimentally demonstrate that by using the proposed method, the coupling efficiency between a SMF-28 and HCF can be increased to the level reachable for straight fibers, which is limited only by a modal fields mismatch. We also present detailed numerical and analytical studies of the coupling efficiency between a HCF and SMF versus the pitch distance in the partially untwisted input section of the HCF, which takes into account fundamental and higher-order modes.

Sub-Doppler Double-Resonance Spectroscopy of Methane Using a Frequency Comb Probe.

We report the first measurement of sub-Doppler molecular response using a frequency comb by employing the comb as a probe in optical-optical double-resonance spectroscopy. We use a 3.3 µm continuous wave pump and a 1.67 µm comb probe to detect sub-Doppler transitions to the 2ν_{3} and 3ν_{3} bands of methane with ∼1.7 MHz center frequency accuracy. These measurements provide the first verification of the accuracy of theoretical predictions from highly vibrationally excited states, needed to model the high-temperature spectra of exoplanets. Transition frequencies to the 3ν_{3} band show good agreement with the TheoReTS line list.

In-Plane Strain Measurement in Composite Structures with Fiber Bragg Grating Written in Side-Hole Elliptical Core Optical Fiber.

In this paper, the application of a fiber Bragg grating written in a highly birefringent side-hole elliptical core optical fiber for two-axial strain measurement is presented. Hybrid optical fiber structures achieved by combining large side-holes and elliptical core result in a very high birefringence of 1 × 10-3 and thus high initial Bragg peak spectral separation of 1.16 nm, as well as a very high transverse force sensitivity, of up to 650 pm/(N/mm) or even -1150 pm/(N/mm), depending on the fiber orientation with respect to the applied force. Due to the ~22 %m/m GeO2 concentration in the core the fiber being highly photosensitive, which significantly simplifies FBG fabrication by UV illumination without the need for prior hydrogen loading, which worsens thermal stability. Finally, the developed FBGs written in the highly birefringent side-hole elliptical core optical fiber were embedded in the square composite plates and applied for strain measurements. Tests of two-directional four-point bending have shown usability of such FBG for two-axial in-plane strain measurement with a single FBG in iso-thermal conditions.

Temporal fine structure of all-normal dispersion fiber supercontinuum pulses caused by non-ideal pump pulse shapes.

We experimentally investigate the spectro-temporal characteristics of coherent supercontinuum (SC) pulses generated in several implementations of silica and soft-glass all-normal dispersion (ANDi) photonic crystal fibers optimized for pumping with Erbium (Er):fiber femtosecond laser technology. We characterize the resulting SC using time-domain ptychography, which is especially suitable for the measurement of complex, spectrally broadband ultrashort pulses. The measurements of the ANDi SC pulses reveal intricate pulse shapes, considerable temporal fine structure, and oscillations on time scales of < 25 femtoseconds, which differ from the smoothness and simplicity of temporal profiles obtained in numerical simulations and observed in previous experiments. We link the measured complex features to temporal sub-structures of the pump pulse, such as pre- and post-pulses and low-level pedestals, which are common in high pulse energy ultrafast Er:fiber systems. We also observe spectro-temporal structures consistent with incoherent noise amplification in weakly birefringent fiber samples. Our results highlight the importance of the pump source and polarization-maintaining (PM) fibers for high-quality SC generation and have practical relevance for many ultrafast photonics applications employing ANDi fiber-based SC sources.

Enhancement of spectral response of Bragg gratings written in nanostructured and multi-stepped optical fibers with radially shaped GeO2 concentration.

We present experimental results on fiber Bragg gratings inscription in nanostructured graded-index (nGRIN) and multi-step index (MSIN) optical fibers, both having non-uniform radial distribution of GeO2 dopant in the fiber cores. In particular, the positive role of radial shaping the GeO2 distribution in the fiber core on grating reflection efficiency is reported. We postulate that an appropriate spatial distribution of the germanium concentration that matches the fundamental mode profile improves grating spectral response due to more efficient grating-mode interaction, as compared with uniformly doped step-index optical fibers with the same overall doping level. Moreover, we show that radially shaped fibers exhibit moderately higher temperature responses than their step-index counterparts.

Bend-induced long period grating in a helical core fiber.

We report on a new type of long-period-grating generated in a helical core fiber by bending. The grating arises from bend-induced modulation of an equivalent refractive index in the helical core with a period equal to the helix pitch. We experimentally demonstrate that such grating induces multiple resonant couplings between the fundamental modes guided in the central core and the helical side-core. We have also shown that by varying a direction of bending, one can generate the phase shifted grating. The experimental results are supported by numerical simulations based on the coupled mode equations.

Stabilized all-fiber source for generation of tunable broadband fCEO-free mid-IR frequency comb in the 7 - 9 µm range.

A compact and robust all-fiber difference frequency generation-based source of broadband mid-infrared radiation is presented. The source emits tunable radiation in the range between 6.5 µm and 9 µm with an average output power up to 5 mW at 125 MHz repetition frequency. The all-in-fiber construction of the source along with active stabilization techniques results in long-term repetition rate stability of 3 Hz per 10 h and a standard deviation of the output power better than 0.8% per 1 h. The applicability of the presented source to laser spectroscopy is demonstrated by measuring the absorption spectrum of nitrous oxide (N2O) around 7.8 µm. The robustness and good long- and short-term stability of the source opens up for applications outside the laboratory.

Method for direct coupling of a semiconductor quantum dot to an optical fiber for single-photon source applications.

We present an effective method for direct fiber coupling of a quantum dot (QD) that is deterministically incorporated into a cylindrical mesa. For precise positioning of the fiber with respect to the QD-mesa, we use a scanning procedure relying on interference of light reflected back from the fiber end-face and the top surface of the mesa, applicable for both single-mode and multi-mode fibers. The central part of the fiber end-face is etched to control the required distance between the top surface of the mesa and the fiber core. Emission around 1260 nm from a fiber-coupled InGaAs/GaAs QD is demonstrated and its stability is proven over multiple cooling cycles. Moreover, a single photon character of emission from such system for a line emitting above 1200 nm is proven experimentally by photon autocorrelation measurements with an obtained value of the second order correlation function at zero time-delay well below 0.5.

Compact all-fiber source of coherent linearly polarized octave-spanning supercontinuum based on normal dispersion silica fiber.

We report the generation of coherent octave-spanning supercontinuum in an all-fiber system, without any free-space optical components. The setup uses the femtosecond fiber laser as a pump and an all-normal dispersion microstructured fiber as a medium for supercontinuum generation. The generated spectrum is characterized both experimentally and numerically and shows a broad bandwidth (1.1-2.2 µm), a high signal to noise ratio reaching 100 at maximum, a high coherence (closing to 1), linear polarization and average output power up to 57 mW. The source is characterized by exceptional simplicity and does not require any alignment (the nonlinear fiber is spliced to the pump) which finally opens the path to outside-lab applications of supercontinuum radiation.

Polarimetric Sensitivity to Torsion in Spun Highly Birefringent Fibers.

We report on experimental studies of polarimetric sensitivity to torsion in spun highly birefringent fibers. Two classes of spun fibers were examined, namely spun side-hole fibers and birefringent microstructured fibers with different birefringence dispersion, spin pitches, and spin directions. The polarimetric sensitivity to torsion was determined by monitoring a displacement of the spectral interference fringes arising in the output signal because of interference of polarization modes and induced by an additional fiber twist. Both the experimental results and the analytical predictions showed that the sensitivity to torsion normalized to the fringe width in the spun highly birefringent fibers increased asymptotically with the twist rate to the value of 1/ π rad-1. We have also studied the polarimetric response to temperature in the spun side-hole fibers. We have found that, in contrast to the torsional sensitivity, the temperature sensitivity decays asymptotically to zero with increasing fiber twist rate. Therefore, the spun fibers with short spin pitches are especially well suited for torsion measurements because the torsional sensitivity and the range of linear response are both enhanced in such fibers, while at the same time, the cross-sensitivity to temperature is reduced.

Experimental Analysis of Bragg Reflection Peak Splitting in Gratings Fabricated Using a Multiple Order Phase Mask.

We performed an experimental analysis of the effect of phase mask alignment on the Bragg grating reflection spectra around the wavelength of λB = 1560 nm fabricated in polymer optical fiber by using a multiple order phase mask. We monitored the evolution of the reflection spectra for different values of the angle ϕ by describing the tilt between the phase mask and the fiber. We observed that the peak at λB is split into five separate peaks for the nonzero tilt and that separation of the peaks increases linearly with ϕ. Through comparison with theoretical data we were able to identify the five peaks as products of different grating periodicities, which are associated with the interference of different pairs of diffraction orders on the phase mask.

IR femtosecond pulsed laser-based fiber Bragg grating inscription in a photonic crystal fiber using a phase mask and a short focal length lens.

Fiber Bragg grating inscription with infrared femtosecond pulsed lasers in photonic crystal fiber is far from being trivial due to the presence of air holes in the cladding region and the non-linear nature of the absorption process inducing the required refractive index changes. We have studied this problem numerically and experimentally for a phase mask-based writing setup equipped with short focal length cylindrical lenses, which are often used for through-coating and high temperature stable grating writing. We have shown that for a cylindrical lens with a focal length f of 10 mm, the hexagonal lattice PCF needs to be translated away from the beam waist position by around 15 µm to efficiently deliver the energy to the core region. We have also investigated the importance of the PCF's angular orientation and we have shown that for some optimal positions the same behavior is observed for cylindrical lenses with different focal lengths. Finally, we have succeeded in writing a 4 dB strong grating in a photonic crystal fiber with a 1030 nm femtosecond pulsed laser in around 4 seconds, using an acylindrical lens with f = 10 mm.